I’m thinking about upgrading my W-Fi and I was curious what wireless access points (WAP) people are using. I’m currently using a Netgear R7800 running OpenWRT.
You must log in or register to comment.
I use a cudy wr3000. Great value for the price and features official openwrt support.
I’m using a couple of TP-Link EAP225 ceiling-mounted PoE access points, and one EAP235-wall wall-mounted one, connected to my old TP-Link Archer C7 router (with the antennas disabled) running OpenWRT.
I’d like to replace the router with something rack-mounted, but haven’t gotten around to it yet.
Went all in with UniFi some time back. No regrets.
Currently running a few U6s. No real motivation to upgrade to U7s.
While expensive, UniFi hardware is just a huge step beyond the rest of the consumer market.
I’ve had literally 10x the range (5x vs 50m), in congested environments, compared to ‘gaming’ hardware. I actually did a side by side to test. I was shocked at the difference.
The bridging function is also a life saver. 2 LR units can get a reliable signal between each other, at ridiculous ranges.
+1 on this. Though i picked up 2 u7’s. VLAN support, easy to maintain and lets face it, superior function from most retail APs. If you’re a power user, this is the way.
I bought a Grandstream GWN7660 last year and it seems pretty good, it replaced a ubiquity WAP that I still have legacy devices connected to.
Fritzbox boxes.
They tick all the checkboxes
- good standards support (including dect protocol if you want to have an ip phone or even iot protocols)
- fast wifi speeds
- cheap (at least for the second hand in ebay)
- super stable, never had a problem with them in 5 years or more
- fast roaming support out of the box
It is a well known brand in Germany but pretty unknown outside that country. Honestly it is the best bang for buck I was able to get.
Honestly, I would spend 10 minutes checking on them
I really like them but they do have two downsides for “more advanced” users (or at least for me) - it is a home device as after all.
- No support for VLAN or VLAN tagging - you can set up you WiFi and a guest WiFi. You can also map the guest network to an Ethernet port. But that’s about it.
- There is no way to change the DNS suffix (*. fritz.box) to another value - I do own a domain that I use for the local services on my home server, etc. which then allows for Let’s Encrypt certificates, but I cannot use it “out of the box”.
If you’re an advanced user, there’s plenty of ways around that, though. I just wished that these two thing were to exist in the firmware to have less work with my home infrastructure.
Totally agree with the first point, it is a limitation, and the guest wifi sticking to a eth port is just a patch. One that works but still a patch.
But I don’t see the point of the prefixes. What do you mean? I also have a custom domain and a local dns server y can use the domain even internally. I just simple ignore that…
Yeah, I’m also using a local resolver. But since I had some problems using another DHCP server (which was probably a problem on my end), so I’m current setting some devices in my FRITZ!box to a fixed IP and then enter that in my DNS server. If I could just skip the second part and tell the FRITZ!Box to just resolve printserver.example.com instead of printserver.fritz.box - that’d be nice. Maybe I should do another try with a DHCP server soon.
Damn those are some serious limitations for an AP.
Ruckus APs with wired backhaul OpnSense box runs the network.
Is Ruckus not crazy expensive? We used it for customers and they are like €500 an access point.
Used on eBay and flashed with the Unleashed firmware. It’s the same price range as Ubiquiti stuff.
I moved to Rukus from Unifi and the difference is night and day. Unifi does not play nice with Sonos and the firmware is rock solid compared to Unifi.
I purchases a few Netgear R6220, and of course flashed OpenWRT on all of them!
Great hardware, cheap, and perfectly supported. A few years old, so I could even find them used at an amazing price point.
TP link EAP’s and i run the omada software controller on an existing server. Right now I have 3 AP’s and it’s been a great experience so far compared to running consumer wifi routers before. All are on ethernet too.
Same, I needed to expand my Wi-Fi and was to lazy to run an Ethernet and a power cable across the attic. I settled for two TP-Link EAP and a TP-Link managed switch that also provides PoE. You can run all three devices stand alone, but Omada is also quite nice - you can run it without using their cloud on your home server and even connect their app to your local controller.
RT-AX88U it has a ton on high end features
GL.Inet. OpenWRT at the core, and a solid hardware base to run on.
I love that GL.iNet stuff ships with OpenWRT (or apparently FreeRTOS in the case of the Thread border router I’m eyeing right now), but I wish they would make stuff like ceiling or wall-mounted PoE access points and rack-mountable wired routers. The form-factor is what stops me from choosing them over TP-Link devices that I have to flash OpenWRT onto myself.
I have 2x Tplink EAP 610 access points. Linking back to an Opnsense virtualized router. The APs are great and Omada is fantastic - I’m running it in a docker container with no cloud access required.
I would go all Omada if I could but that would mean I’d need 3 POE Omada switches and I cant justify that cost at the moment.
And sadly Omada is years behind in their gateway/Firewall. OPNsense is far better in that regard, going back to a Omada gateway is like going back to a tricycle when you drive a car. Sadly.
I was meaning their switches. I didn’t know they did routers / firewalls. Interesting that they’re not as advanced as their other offerings which are really good. My opnsense setup has taken years to hone and I have no desire to start over with that.
Unifi. I’ve got a box of APs as ewaste just sitting in the basement. Every so often I would get more ewaste from companies I work with.
I don’t need the most demanding of wifi systems. I hardwire most of my stuff whenever possible. And I have a fairly small home. A single AP on the main floor, 1 AP on the basement. 1 AP in the detached garage.
Most of my wifi devices are iot things on their own vlan.
I use the tp-link EAP615 wall Apps, they are great and run OpenWRT like a champ.
Its not for everyone but I use Cisco Aironet APs with a virtual wireless LAN controller. Ubiquiti is popular among the community. They’re cost effective and work well in a home/small business environment. Aruba InstantOn are decent as well from my experience, but they’re cloud managed and this is self-hosted after all :)
I’ve extensively used Cisco, Meraki, Fortinet, Cambium, Aruba, Ubiquiti and Juniper in a professional setting. Avoid Fortinet and Cambium APs if you can, my experience is that they can be pretty unstable.
Generally speaking if you’re going to have multiple APs, you’ll want something that’s centrally managed so the APs are able to be aware of each other and manage clients effectively.
2nd hand Ruckus.
They’re decent quality that you’d see in a commercial / enterprise setting (so PoE), but Ruckus also have their “Unleashed” firmware which removes the need for a WLC.
I have 2 in a mesh at home and easily support many IoT devices, phones, laptops, etc on multiple SSIDs
