Hi everyone!

I’m curious to know which slicer you guys use.

I’ve been using the Creality slicer, but it seems like it pretty consistently crashes, and I’ve tried Cura but the print seemed stringy despite using the same settings.

How are Orca or Prusa?

  • chris@l.roofo.ccEnglish
    17·
    11 months ago

    PrusaSlicer. I like the settings better. It’s a good slicer.

    • Fubarberry@sopuli.xyzEnglish
      6·
      11 months ago

      I had some issues early on with Cura and switched to Prusa, and it’s always worked well for me.

  • charmed_electron@programming.devEnglish
    8·
    11 months ago

    Another vote for prusa here. The recently added organic supports are really awesome. It’s enabled me to print some things I previously would not have attempted.

  • Stephen304@lemmy.mlEnglish
    7·
    11 months ago

    Prusa slicer, partially because I have a mk3s+ but also because I tried to use cura many times but always several minutes into using it, my entire laptop just shuts off, like the power was pulled, no logs written to disk, no error message. It’s the only program to do that and I can’t even report an issue because there’s no logs I can submit. I assume it’s related to taxing my GPU in a way that causes a power related fault.

  • na_th_an@lemmy.worldEnglish
    6·
    11 months ago

    I used Cura for a few years, then I tried Prusa and my print quality dramatically improved for reasons I have not figured out.

    • Rakqoi@lemmy.blahaj.zoneEnglish
      3·
      11 months ago

      Haha this is exactly my experience. Pusaslicer/superslicer just make such better prints for me and I have no idea why. Despite putting so much effort into my Cura settings, Prusa just prints better out of the box with so little effort.

    • IMALlama@lemmy.worldEnglish
      3·
      11 months ago

      I used Cura about 5 years ago and my experience then was actually the inverse, especially in regards to slicing settings. There were tons of settings buried all over the GUI and you really had to dig for them.

      I used KISSSlicer for a while and got into PrusaSlicer. They all seem to have their struggles from time to time. Maybe I’ll try out Cura again the next time I run into a wall.

      • KyuubiNoKitsune@lemmy.blahaj.zoneEnglish
        4·
        11 months ago

        By default all the settings are hidden, it’s annoying, but you can show all of them in the settings and then it has a bunch more that I can find equivalents to in Prusa.

  • lapis@lemmy.blahaj.zoneEnglish
    61·
    11 months ago

    Another OrcaSlicer user here. Started off with PrusaSlicer and switched over at a friend’s recommendation, and honestly am so glad I did (it has a much nicer UI and some really neat features ported over from SuperSlicer).

  • empireOfLove@lemmy.oneEnglish
    4·
    11 months ago

    I’ve almost always used PrusaSlicer just because the only printers I had access to were mk3s+.

    I’ve started playing with Cura though because A. i wanted some more complex prints that PrusaSlicer struggled to support, and B. We also got some creality cr-30’s functional at my college again. So far I still feel Prusa is easier but that’s likely just familiarity.

  • GrayBackgroundMusic@lemm.eeMEnglish
    31·
    11 months ago

    Whichever one works. I switch between Cura and PS. I’m not skilled enough to figure out the differences. I make small adjustments here and there, but IDK what I’m doing. My last print had over extrusion on the top surface, but not the walls, so I switched from Cura to PS and it works now.