I decided on cleaning my laptop fans today, which I’ve been procrastinating for about a year now because of this one screw. But I just can’t seem to open this with my screwdriver, since whatever I did back when I last opened it it’s nearly circular now. Is there a way to unscrew this?
Carefully dremel a slot in the screw head and use a flat head screwdriver.
Make sure you don’t get any dust into the electronics.
Jb weld a nut to it.
Also, G Flex is an epoxy formulated for plastics and West Systems has tutorials on their site.
In this case, I’d drill a small hole in the center, put CA or epoxy in it, then screw another screw into the epoxied hole and let it set up.
There’s no need for all that work. Just a dab of epoxy or glue right on top, the any appropriate sized nut on top of that.
Any drilling/dremel work just creates dust and metal shavings.
I think the answer is no.
So if you have a dremel and steady hands, a cut off wheel can make your own slot for a straight Phillips.
Just be careful to not knick anything else. This is more of a last resort thing, but I’ve never had it not work.
Learn from my mistakes, mask off your laptop’s ports and vents before you do this
Ooof. Not something I’d have thought of myself…
Benefit of your hindsight it’s obvious… lol. How bad were the sparks?
Surprisingly quiet, one little ‘pop’ was the last I heard from that motherboard. On-board power supplies were a reasonable step forward but man are they not fault tolerant
Keyboard too?
Yes
I came here to say that
Flathead/standard not a straight Philips.
Flathead is a description of the head profile, like panhead. Slotted is the screwdriver type that is just a single slot.
It could be a regional thing. Where I’m from a screw with a single straight slot can be called a flathead whether the actual head of the screw is flat or domed.
It gets called that everywhere. Most people never need to know the actual specs for a screw, so language diverges from the classification system.
I usually keep the corrections to myself, but when somebody else is already correcting someone and they say the wrong thing too it becomes hard.
Amazon search for tiny screw extractor.
If its big enough, try the rubber band trick to get some grip.
If its a tiny electronic screw, you’ll have to very carefully coax it out with either some needle nose pliers by gripping the outside, or by using a slightly larger screwdriver head and ensuring it doesn’t spin (very tricky, easy to strip screw further, using rubber band here might also help).
If the case can handle it, you can use the larger head and give it some decent amount of pressure to make sure it doesn’t spin when you turn. Again be careful, because pushing too hard could break the case.
You might have to inch it fractions of a turn at a time to make sure it doesn’t break, so it’ll take a while before it becomes loose enough to spin out by hand.
Put a rubber band between screwdriver and screw, otherwise the other things already stated like CA glue, filing a flathead groove, or drilling the cap off
in the future use the appropriate sized driver and retire drivers when they become stripped
This. The rubber band trick works well for the first step. I came to say this.
The rubber band trick is great, and very low effort/cost. I want to say, though, that it can take substantially more force than it looks like it should on small screws like this. You also don’t have to use something shaped for the original driver of the screw. With the rubber to help it, a round cylinder a little smaller than the head of the screw can work very well.
Just so you know, OP, CA glue is a generic term for CyanoAcrylate glue, like Super Glue or Krazy Glue.
Bring out the KraGle!
It looks like you probably don’t have enough edge for this, but a simple vise grip could work.
This was my first thought also. The defcon 2 solution. If that doesn’t work, the next step is to drill it out.
If you didn’t have a Dremel, try channel lock pliers or vise grips. It’s not going to be in there right and rusted or anything, you just need something to grip it.
A dab of super glue in the screw hole, find a screw driver you don’t really care about, add a drop of superglue accelerator
Depending how tight it is you could superglue something to it to turn it ?
I don’t really have superglue right now, and the screw looks like this far up, not sure it can be called tight or not.
(Screwdriver for comparison, couldn’t really find something better.)
You could also padding out the screwdriver tip or the screw hole. I’ve used sticky tape before, but again if its tight your pretty much out of luck…
That would have to be a pretty loose screw
Pretty much this - depending how much surface area and how good the glue is you might get it or you might snap that right off too. If it fails the next step is to carefully drill the screw out. A somewhat riskier operation but itll get it open
Try addinv a rubber band between the screw and the screwdriver, it adds friction which sometimes (usually not) helps
Id probably try a pair of pliers
I prefer the rubber band trick first but usually when I get them down to this point I’ll use a smaller flathead from a jeweler set, see if you can find something that fits in between the two opposing tines of the Philips
Oooh man - you’re screwed!
